# 🔌 How difficult is it to install the ELEGRP USB Outlets Receptacle?

*Published: 2024-03-18 | Updated: 2024-09-20 | Source: https://shopsavvy.com/answers/how-difficult-is-it-to-install-the-elegrp-usb-outlets-receptacle*

---

## Product: ELEGRP USB C Wall Outlet (10 Pack)
**Brand:** ELEGRP

Installing the ELEGRP USB Outlets Receptacle might seem a bit intimidating at first, but if you've got some basic electrical knowledge, you'll be fine. Here’s a quick guide to help you through it and let you know what to expect in terms of difficulty. 

### What You'll Need

1. **[Circuit Tester](https://www.shopsavvy.com/redirect?url=https%3A%2F%2Fwww.amazon.com%2Fs%3Fk%3Dcircuit%2Btester%26tag%3Dssw.ans.tx-1-20)**: To make sure the power is off before you start.

2. **[Screwdrivers](https://www.shopsavvy.com/redirect?url=https%3A%2F%2Fwww.amazon.com%2Fs%3Fk%3Dscrewdrivers%26tag%3Dssw.ans.tx-1-20)**: Both a flathead and a Phillips screwdriver.

3. **[Wire Strippers](https://www.shopsavvy.com/redirect?url=https%3A%2F%2Fwww.amazon.com%2Fs%3Fk%3Dwire%2Bstrippers%26tag%3Dssw.ans.tx-1-20)**: For prepping the wires.

4. **[Electrical Tape](https://www.shopsavvy.com/redirect?url=https%3A%2F%2Fwww.amazon.com%2Fs%3Fk%3Delectrical%2Btape%26tag%3Dssw.ans.tx-1-20)**: To secure the connections.

5. **[New Wall Plate](https://www.shopsavvy.com/redirect?url=https%3A%2F%2Fwww.amazon.com%2Fs%3Fk%3Dnew%2Bwall%2Bplate%26tag%3Dssw.ans.tx-1-20) (Optional)**: If you want a fresh look to go with your new outlet.

### Step-by-Step Installation Guide

1. **Turn Off Power**: Go to your circuit breaker and turn off the power for the outlet you’re replacing. Use the circuit tester to verify that the outlet is dead.

2. **Remove Old Outlet**: Unscrew the faceplate and the screws holding the outlet in the box. Pull the outlet out carefully but leave the wires attached so you can see how they're connected.

3. **Disconnect Wires**: Take note (or a photo) of how the wires are connected and then disconnect them. Typically, you'll see a black (hot), white (neutral), and green or bare (ground) wire.

4. **Prepare the New Outlet**: The manufacturer mentions that the ELEGRP USB Outlets Receptacle fits a standard electrical box, so you shouldn't need any extra adjustments.

5. **Connect the Wires**: Attach the wires to the new outlet—black to the brass screw (hot), white to the silver screw (neutral), and green or bare wire to the green screw (ground). Tighten the screws securely.

6. **Install the Outlet**: Tuck the wires back into the electrical box carefully, then screw the new outlet into place. Attach the faceplate.

7. **Turn the Power Back On**: Head back to the circuit breaker and turn the power back on. Test the outlet with a small device to ensure it's working.

### Troubleshooting Tips

- **Loose Wires**: Double-check that all wires are securely attached, and the screws are tight.

- **Incorrect Wiring**: Make sure all connections are correct according to the manufacturer’s instructions to avoid any mistakes.

- **Circuit Breaker Issues**: If the outlet isn’t working, you might need to reset the breaker again.

### What Others Said

According to our research, many people found the installation pretty straightforward, especially if they'd done electrical work before. Plus, the detailed guide from the manufacturer was a big help. 

However, if you’re not comfy with electrical stuff, you might want to consult a pro to make sure everything’s safe and properly installed.

Following these steps and keeping a few tips in mind should make installing your ELEGRP USB Outlets Receptacle a breeze, adding some handy USB ports to your home.

---

*Where this comes from: This answer is based on ShopSavvy's product database, real-time pricing from thousands of retailers, and analysis of user reviews to give you a well-rounded picture.*